ultrasonic signal can be obtained. In contact ultrasonic testing a thin film of oil, glycerin or water is generally used between the transducer and the test surface.
When scanning over the part or making precise measurements, an immersion technique is often used. In immersionultrasonic testing both the transducer and the part are immersed in the couplant, which is typically water. This method of
What is Bioenergy?
Bioenergy is renewable energy made available from materials derived from biological sources. Biomass is any organic material which has stored sunlight in the form of chemical energy. As a fuel it may include wood, wood waste, straw, manure, sugarcane, and many other byproducts from a variety of agricultural processes.
So, Why do we produce Bioenergy?
One reason governments
Abstract
Bioethanol is one of the alternative sources of oil resources which received attention with biodiesel. Many countries produce bioethanol from food sources such as corn and sugarcane, but it causes food-energy conflicts and farmland problem. So it needs to focus on new biomass which is sustainable, renewable, cost-effective and do not occurred any conflicts. Algae are one of the bioma
기존 접착제는 접착소재와 칩, 기판간의 열팽창계수 차이에 의한 박리, 크래킹 등이 문제.
CNT/epoxy 나노 복합체를 통해 해결.
하나의 탄소가 다른 탄소원자와 육각형 벌집무늬로 결합되어 튜브형태를 이루고 있는 물질
튜브의 직경이 나노미터(nm=10-9m) 수준으로 극히 작은 영역의 물질
멸균(sterilization)
대상물체에 존재하는 균을 완전히 박멸시키는 조작이다. 살균(균을 죽임)과는 조금 틀린 개념이다. 살균은 끓는 물(수증기)로 균을 죽이는 것을 말한다. 그러나 멸균처럼 균속의 포자등까지 죽이지는 못한다. 건조 ․일광조사 ․자외선 ․방사선 등은 소독에 이용된다. 0℃ 부
ultrasonication이나 D-cycloserine treatment가 흔히 사용된다. 그러나 이러한 방법은 복잡하고 시간이 많이 소요되며 경제적이지 못하다. 특히 대량으로 screening 할 경우, 이 단계를 생략하는 것이 많은 장점이 있다. 따라서 쉽고 경제적인 방법의 연구 개발이 필요한 실정이다. 올해 개발된 pBlueLysis vector system은 pr
Introduction
Corroded heat element of GGH
Ref. 박승수․안희수․김기형․박광규, 배연탈황설비 Gas-Gas-Heater(GGH) Heat element 부식 원인규명, 한국대기환경학회 2006 추계학술대회 논문집
Pitting corrosion in a storage tank floor
Ref. M.B. Hoppenbrouwers MScRntgen Technische Dienst BV, Rotterdam, Advanced Ultrasonic Methods For In Ser
Density of steel 7800
Poisson’s ratio 0.32
The resultant data(velocity) = 5666.7
From this formula, we could determine the modulus of elasticity,
Theoritical value of E of steel is 200GPa, error would be
Fig.1 Property of materials.
2. Considerations
We could figure out material's properties and method of finding defect of the specimen. Ultrasonic wave value was alm
특성시험
① 인장시험 ② 전단시험 ③ 굴곡시험 ④ 압축시험 ⑤ 층간 전단강도 시험
4. 파괴 및 피로 특성시험
① 파괴 특성시험 ② 피로 특성시험 ③ 파단면 분석
5. 비파괴 시험법
① 초음파 탐상법 ② X선 투과시험법 ③ 음향방출 시험법 ④ acousto-ultrasonic 시험법
⑤ 적외선 시험법
6. 환경시험